DEVICE DESCRIPTION
The CAT24C03/CAT24C05 is a 2-kb/4-kb CMOS Serial EEPROM device organized internally as 16/32 pages of 16 bytes each, for a total of 256x8/512x8 bits. These devices support both Standard (100kHz) as well as Fast (400kHz) I2C protocol.
Data is written by providing a starting address, then loading 1 to 16 contiguous bytes into a Page Write Buffer, and then writing all data to non-volatile memory in one internal write cycle. Data is read by providing a starting address and then shifting out data serially while automatically incrementing the internal address count.
Write operations can be inhibited for upper half of memory by taking the WP pin High.
External address pins make it possible to address up to eight CAT24C03 or four CAT24C05 devices on the same bus.

FEATURES
*Supports Standard and Fast I2C Protocol
*1.8 V to 5.5 V Supply Voltage Range
*16-Byte Page Write Buffer
*Hardware Write Protection for upper half of memory
*Schmitt Triggers and Noise Suppression Filters on I2C Bus Inputs (SCL and SDA).
*Low power CMOS technology
*1,000,000 program/erase cycles
*100 year data retention
*Industrial temperature range
*RoHS-compliant 8-lead PDIP, SOIC, and TSSOP, 8-pad TDFN and 5-lead TSOT-23 packages.

CAT24C05  

CAT24C03 - 2-Kb and 4-Kb I2C Serial EEPROM with Partial Array Write Protection

DESCRIPTION
The CAT5128 is a single digitally programmable potentiometer (DPP™) designed as an electronic replacement for mechanical potentiometers and trim pots. Ideal for automated adjustments on high volume production lines, they are also well suited for applications where equipment requiring periodic adjustment is either difficult to access or located in a hazardous or remote environment.
The CAT5128 contains a 32-tap series resistor array connected between two terminals A and B. An up/down counter and decoder that are controlled by two input pins, determines which tap is connected to the wiper, W. Wiper-control of the CAT5128 is accomplished with two input control pins, U¯¯P and ¯D¯O¯W¯¯N¯. A high-to-low transition on the U¯¯P input increments the wiper position and a high-to-low transition on the ¯D¯O¯W¯¯N¯ input decrements the wiper position. The tap position is not stored in memory. The wiper is always set to the mid point, tap 15 at power up.
The digitally programmable potentiometer can be used as a three-terminal resistive divider or as a two-terminal variable resistor. DPPs bring variability and programmability to a wide variety of applications including control, parameter adjustments, and signal processing.

FEATURES
*32-position linear taper potentiometer
*Low power CMOS technology
*Single supply operation: 2.5V – 5.5V
*Discrete step-up/step-down digital control
*Resistance values: 10kΩ, 50kΩ and 100kΩ
*Available in SOT-23 8-lead Pb-free package

APPLICATIONS
*Automated product calibration
*Remote control adjustments
*Offset, gain and zero control
*Tamper-proof calibrations
*Contrast, brightness and volume controls
*Motor controls and feedback systems
*Programmable analog functions

CAT5128TBI-10, CAT5128TBI-50, CAT5128TBI-00  

CAT5128 - 32-Tap Digital Up/Down Control Potentiometer

DESCRIPTION
The CAT28F512 is a high speed 64K x 8-bit electrically erasable and reprogrammable Flash memory ideally suited for applications requiring in-system or after-sale code updates.
Electrical erasure of the full memory contents is achieved typically within 0.5 second.
It is pin and Read timing compatible with standard EPROM and E2PROM devices.
Programming and Erase are performed through an operation and verify algorithm.
The instructions are input via the I/O bus, using a two write cycle scheme.
Address and Data are latched to free the I/O bus and address bus during the write operation.
The CAT28F512 is manufactured using Catalyst’s advanced CMOS floating gate technology.
It is designed to endure 100,000 program/erase cycles and has a data retention of 10 years.
The device is available in JEDEC approved 32-pin plastic DIP, 32-pin PLCC or 32-pin TSOP packages.

FEATURES
*Fast Read Access Time: 90/120/150 ns
*Low Power CMOS Dissipation:
-Active: 30 mA max (CMOS/TTL levels)
-Standby: 1 mA max (TTL levels)
-Standby: 100 mA max (CMOS levels)
*High Speed Programming:
-10 ms per byte
-1 Sec Typ Chip Program
*12.0V ± 5% Programming and Erase Voltage
*Electronic Signature
*Commercial, Industrial and Automotive Temperature Ranges
*Stop Timer for Program/Erase
*On-Chip Address and Data Latches
*JEDEC Standard Pinouts:
-32-pi*DIP
-32-pi*PLCC
-32-pi*TSOP ( 8 x 20)
*100,000 Program/Erase Cycles
*10 Year Data Retention

CAT28F512NI-90T
CAT28F512PI-90T  

CAT28F512 - 512K-Bit CMOS Flash Memory

DESCRIPTION
The CAT705, CAT706, and CAT813 provide reset and monitoring functions for the electronic systems.
Each device monitors the system voltage and maintains a reset output until that voltage reaches the device’s specified trip value and then maintains the reset output active condition until the device’s internal timer allows the system power supply to stabilize.

FEATURES
* Accurate under voltage system monitoring
* R¯¯E¯S¯E¯T¯ guaranteed valid for VCC = 1.0V
* 6μA supply current
* 200ms RESET pulse width
* Watchdog timer function 1.6 sec timeout
* Brownout detection system reset for use with 3.0, 3.6, and 5.0 volt systems
* Pin and function compatible with the MAX705/706/813L products
* Operating Range from -40°C to +85°C
* Available in SOIC 8-lead and MSOP 8-lead packages

APPLICATIONS
* Microprocessor and microcontroller based systems
* Intelligent instruments
* Control systems
* Critical μP monitors
* Portable equipment

 

CAT705 - μP Supervisory Circuits

DESCRIPTION
 The CAT1232LP and CAT1832 microprocessor supervisors can halt and restart a “hung-up” or “stalled” microprocessor, restart a microprocessor after a power failure, and debounce a manual/push-button microprocessor reset switch.
The devices are drop in replacements for the Maxim/Dallas Semiconductor DS1232LP and DS1832 supervisors Precision reference and comparator circuits monitor the 5V or 3.3V system power supply voltage, VCC.
During power-up or when the power supply falls outside selectable tolerance limits, both the RESET and RESET¯¯¯¯¯¯ become active.
After the power supply voltage rises above the RESET threshold voltage, the reset signals remain active for a minimum of 250ms, allowing the power supply and system processor to stabilize.
The trip-point tolerance input, TOL, selects the trip level tolerance to be either 5% or 10% for the CAT1232LP 5V supply and 10% or 20% for the CAT1832 3.3V supply.
Each device has a push-pull, active HIGH reset output.
The CAT1232LP also has an open drain, active LOW reset output while the CAT1832 also has a push-pull, active LOW reset output.
A debounced manual reset input activates the reset outputs and holds them active for a minimum period of 250ms after being released.
Also included is a watchdog timer to reset a microprocessor that has stopped due to a software or hardware failure.
Three watchdog time-out periods are selectable: 150ms, 600ms and 1.2s. If the ST¯¯ input is not strobed low before the watchdog time out period expires, the reset signals become active for a minimum of 250ms.

FEATURES
* Selectable reset voltage tolerance
- CAT1232LP for 5V supply
- CAT1832 for 3.3V supply
* Selectable watchdog period: 150ms, 600ms or 1.2s
* Two reset outputs
- Active high, push-pull reset output
- Active low, open-drain reset output (CAT1232LP)
- Active low, push-pull reset output (CAT1832)
* Debounced manual push-button reset
* Compact SOIC and MSOP packages

APPLICATIONS
* Microprocessor Systems
* Portable Equipment
* Controllers
* Single Board Computers
* Instrumentations
* Telecommunications

CAT1232LPL-G
CAT1232LPV-GT3
CAT1232LPZ-GT3
CAT1232LPW-T2

 

CAT1232 - 5V and 3.3V Supply Monitor, Watchdog Timer, Manual Reset, with Active High & Low Resets