DESCRIPTION
The 12P10 uses advanced proprietary, planar stripe, DMOS technology to provide excellent RDS(ON), low gate charge and operation with low gate voltages. This device is suitable to be
used in low voltage applications such as audio amplifier, high efficiency switching DC/DC converters, and DC motor control.

FEATURES
*RDS(ON) = 0.29Ω @VGS = -10 V
*Low capacitance
*Low gate charge
*Fast switching capability
*Avalanche energy specified

12P10-TN3-R, 12P10-TN3-T  

12P10 - 100V P-CHANNEL MOSFET

FEATURES
*High total power dissipation. (625mW)
*High collector current. (-500mA)
*Excellent hFE linearity
*Complementary to UTC 9013

 

UTC9012 - PNP EPITAXIAL SILICON TRANSISTOR

DESCRIPTION
The UTC 7N60L is a high voltage MOSFET and is designed to have better characteristics, such as fast switching time, low gate charge, low on-state resistance and have a high rugged avalanche characteristics.
This power MOSFET is usually used at high speed switching applications in switching power supplies and adaptors.

FEATURES
* RDS(ON) = 1.2Ω @VGS = 10 V
* Ultra low gate charge (typical 29 nC )
* Low reverse transfer Capacitance ( CRSS = typical 16pF )
* Fast switching capability
* Avalanche energy tested
* Improved dv/dt capability, high ruggedness

7N60L-x-TA3-T
7N60L-x-TF3-T  

7N60L - 7.4 Amps, 600/650 Volts N-CHANNEL MOSFET

DESCRIPTION
 The UTC PA0202 is a monolithic integrated circuit that stereo bridged audio power amplifiers capable of producing 2 W into 3Ω with a 5V supply voltage or 800mW into 3Ω with a 3.3V supply
voltage.
The UTC PA0202 simplifies design and frees up board space for other features.
Both of the depop circuitry and the thermal shutdown protection circuitry are integrated in UTC PA0202, that reduce clicks and pops noise during power up or shutdown mode operation.
A MUX control terminal (HP/LINE) allows selection between the two sets of stereo input signals.
To simplify the audio system design, UTC PA0202 combines a stereo bridge-tied loads (BTL)mode for speaker drive and a stereo single-end (SE)mode for headphone drive into a single chip, where both modes are easily switched by the SE/BTL input control pin signal.

FEATURES
* Improves depop circuitry to eliminate turn-on and turn-off transients in output
* Output power:
- 2W(typ.)@5V into 3Ω with 0.2% THD+N max (1kHz)
- 800mW(typ.)@3.3V into 3Ω with 0.2% THD+N max (1kHz)
* Fully specified for use with 3-Ω Loads
* Stereo switchable bridged/single-ended power amplifiers
* Input MUX select terminal
* Thermal-shutdown protection
* Shutdown mode available

PA0202-N24-R
PA0202-N24-T
PA0202L-N24-R
PA0202L-N24-T  

PA0202 - 2-W STEREO AUDIO POWER AMPLIFIER WITH MUTE

DESCRIPTION
The UTC LR1108 operate from a +2.5V ~ +7.0V input supply as fast ultra low-dropout linear regulators. Wide output voltage range options are available. The fast response characteristic to make UTC LR1108 suitable for low voltage microprocessor application.
The low quiescent current operation and low dropout quality caused by the CMOS process.
The UTC LR1108 has ultra low dropout voltage; 300mV at 600mA load current typically.
The ground pin current is typically 200uA at 1mA load current. ERROR Flag: When the output voltage drops 10% below nominal value Error flag goes low.
Output Voltage Precision: Multiple output voltage options are available and ranging from 1.2V ~ 5.0V at room temperature with a guaranteed accuracy of ±1.5%, and ±3.0% when varying line, load and temperature.

FEATURES
* Ultra low dropout voltage
* Low ground pin current
* 0.04% load regulation
* The guaranteed output current is 1A DC
* Output voltage accuracy ± 1.5%
* ERROR flag indicates output status
* Low output capacitor required
* Overtemperature protection and overcurrent protection

LR1108-15-AF5-R
LR1108L-15-AB3-A-R
LR1108L-15-AB3-C-R

 

LR1108 - 1A FAST ULTRA LOW DROPOUT LINEAR REGULATOR