Description
Clare and IXYS have combined to bring OptoMOS® technology, reliability and compact size to a new family of High Power Solid State Relays. As part of this new family, the CPC1786 single pole normally open (1-Form-A) DC Solid State Relay employs optically coupled MOSFET technology to provide 2500Vrms of input to output isolation.
The output is constructed with an efficient MOSFET switch and photovoltaic die that uses Clare’s patented OptoMOS architecture while the input GaAlAs infrared LED provides the optically coupled control. The combination of low on-resistance and high load current handling capability makes this relay suitable for a variety of high-performance DC switching applications.
The unique i4-PAC package pioneered by IXYS allows solid state relays to achieve the highest load current and power ratings. This package features an IXYS unique process where the silicon chips are soft soldered onto the Direct Copper Bond (DCB) substrate instead of the usual copper leadframe. The DCB ceramic, the same substrate used in high power modules, not only provides 2500Vrms isolation but also very low thermal resistance (0.35°C/W).

Features
*100% Solid State
*Compact i4-PAC™ Power Package
*Low Thermal Resistance (0.35°C/W)
*1.75ADC Load Current with 5ºC/W Heat Sink
*Electrically Non-conductive Thermal Pad for Heat Sink Applications
*No Moving Parts
*Low Drive Power Requirements
*Arc-Free With No Snubbing Circuits
*2500Vrms Input/Output Isolation
*No EMI/RFI Generation
*Machine Insertable, Wave Solderable

Applications
*Industrial Controls
*Motor Control
*Robotics
*Medical Equipment—Patient/Equipment Isolation
*Instrumentation
*Multiplexers
*Data Acquisition
*Electronic Switching
*I/O Subsystems
*Meters (Watt-Hour, Water, Gas)
*Transportation Equipment
*Aerospace/Defense

CPC1786J  

CPC1786 - i4-PAC™ DC Power Relay

Description
The ADNS-3040 is an ultra low-power optical navigation sensor.
It has a new, lowpower architecture and automatic power management modes, making it ideal for battery-and power-sensitive applications such as cordless input devices.
The ADNS-3040 is capable of high-speed motion detection – up to 20 ips and 8G.
In addition, it has an on-chip oscillator and LED driver to minimize external components.
The ADNS-3040 along with the ADNS-3120-001 lens, ADNS- 2220 clip and HLMP-ED80-
PS000 LED form a complete and compact mouse tracking system.
There are no moving parts, which means high reliability and less maintenance for the end user.
In addition, precision optical alignment is not required, facilitating high volume assembly.
The sensor is programmed via registers through a four-wire serial port. It is packaged in a
20-pin DIP.

Features
* Low power architecture
* Self-adjusting power-saving modes for longest battery life
* High speed motion detection up to 20 ips and 8G
* SmartSpeed self-adjusting frame rate for optimum performance
* Motion detect pin output
* Internal oscillator – no clock input needed
* Selectable 400 and 800 cpi resolution
* Wide operating voltage: 2.5V-3.6V nominal
* Four wire serial port
* Minimal number of passive components

Applications
* Optical Mice
* Optical trackballs
* Integrated input devices
* Battery-powered input devices

ADNS3040  

ADNS-3040 - Ultra Low-Power Mouse Sensor

General Description
The AAT4901 FastSwitch™ is a member of AnalogicTech’s Application Specific Power MOSFET™ (ASPM™) product family.
It is a full-bridge buffered power stage operating with an input voltage range of 2.0V to 5.5V.
The device is designed to operate with a switching frequency of up to 2MHz, minimizing the cost and size of external components.
The AAT4901 is protected from shoot-through current by integrated break-before-make circuitry. The drivers can be independently controlled and their propagation delay, from input to output, is typically between 8ns-19ns dependent upon logic option.
Four options are offered providing a single input control, dual input control or as two independent half-bridges.
Other features include low RDS(ON) and low quiescent current allowing for high efficiency performance.
The AAT4901 is available in the space-saving, Pb-free 8-pin SC70JW package and is rated over the -40°C to +85°C temperature range.

Features
* VIN Range: 2.0V–5.5V
* RDS(ON):
- High-side 220mΩ
- Low-side 160mΩ
* Break-Before-Make Shoot–Through Protection
* 4 Options
- Single Control Input with Enable
* Two Logic Versions
- Dual Control Input with Brake Function
- Dual Half-bridge
* Low Quiescent Current:
- 10μA (max) DC
- 4mA (max) at 1MHz
* -40°C to +85°C Temperature Range
* SC70JW-8 Package

Applications
* DC Motor Drive
* Door Locks
* Dual Low-Side MOSFET Gate Driver
* Fan Motors
* High Frequency DC/DC Converters
* High Speed Line Drive
* Proximity Detectors

AAT4901IJS-1-T1
AAT4901IJS-2-T1
AAT4901IJS-3-T1
AAT4901IJS-4-T1  

AAT4901 - Buffered Power Full-Bridge

General Description
 The AP393A consists of two independent precision voltage comparators with an offset voltage specification as low as 8.0mV max for two comparators which were designed specifically to operate from a single power supply over a wide range of voltages.
Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage.
These comparators also have a unique characteristic in that the input common-mode voltage range includes ground, even though operated from a single power supply voltage.
Application areas include limit comparators, simple analog to digital converters; pulse, square wave and time delay generators; wide range VCO; MOS clock timers; multivibrators and high voltage digital logic gates.
The AP393A is designed to directly interface with TTL and CMOS.
When operated from both plus and minus power supplies, the AP393A will directly interface with MOS logic where their low power drain is a distinct advantage over standard comparators.

Features
* Wide supply
  Voltage range: 2.0V to 36V
  Single or dual supplies: ±1.0V to ±18V
* Very low supply current drain (0.4mA) – independent of supply voltage
* Low input biasing current: 150nA
* Low input offset current: ±70nA
* Low input offset voltage: ±4mV
* Input common-mode voltage range includes ground
* Differential input voltage range equal to the power supply voltage
* Low output saturation voltage: 250mV at 4mA
* Output voltage compatible with TTL, DTL, ECL, MOS and CMOS logic systems
* MSOP-8L and SOP-8L: Available in “Green” Molding Compound (No Br, Sb)
* Lead Free Finish/ RoHS Compliant (Note 1)

Applications
* High precision comparators
* Reduced VOS drift over temperature
* Eliminates need for dual supplies
* Allows sensing near ground
* Compatible with all forms of logic
* Power drain suitable for battery operation

AP393AM8G-U
AP393AM8G-13
AP393ASG-U
AP393ASG-13

 

AP393A - LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS

Description
Clare and IXYS have combined to bring OptoMOS®technology, reliability and compact size to a new family of high-power Solid State Relays.
As part of this family, the CPC1908 single pole normally open (1-Form-A) Solid State Power Relay is rated for up to 8.5Arms continuous load current with a 5°C/W heat sink.
The CPC1908 employs optically coupled MOSFET technology to provide 2500Vrms of input to output isolation.
The output is constructed with efficient MOSFET switches and photovoltaic die that use Clare’s patented OptoMOS architecture while the input, a highly efficient GaAlAs infrared LED provides
the optically coupled control.
The combination of low on-resistance and high load current handling capability makes this relay suitable for a variety of high performance switching applications.
The unique i4-PAC package pioneered by IXYS allows Solid State Relays to achieve the highest load current and power ratings.
This package features a unique IXYS process where the silicon chips are soft soldered onto the Direct Copper Bond (DCB) substrate instead of the traditional copper leadframe.
The DCB ceramic, the same substrate used in high power modules, not only provides 2500Vrms isolation but also very low thermal resistance (0.35 °C/W).

Features
* Compact i4-PAC™ Power Package
* Low Thermal Resistance (0.35 °C/W)
* 8.5Arms Load Current with 5°C/W Heat Sink
* Electrically Non-conductive Thermal Pad for Heat Sink Applications
* Low Drive Power Requirements
* Arc-Free With No Snubbing Circuits
* 2500Vrms Input/Output Isolation
* No EMI/RFI Generation
* Machine Insertable, Wave Solderable

Applications
* Industrial Controls
* Motor Control
* Robotics
* Medical Equipment—Patient/Equipment Isolation
* Instrumentation
- Multiplexers
- Data Acquisition
- Electronic Switching
- I/O Subsystems
- Meters (Watt-Hour, Water, Gas)
* Transportation Equipment
* Aerospace/Defense

CPC1908J

 

CPC1908 - i4-PAC™ Power Relay